About 307,000 results
Open links in new tab
  1. Dana 70 FF gear oil capacity | Cummins Diesel Forum

    Mar 3, 2012 · Keep in mind a complete drain of a dana 70 if doing brakes and hub seal will take 3.5 + axle tube and hub cavity. I am using 50% Lucas and 50% 80/90 to refill my '68 Dana 70. It is a summer only driver.

  2. Dana 70 brake conversion kit | Cummins Diesel Forum

    Oct 3, 2024 · I might look at this kit Dodge Dana 70 Disc Brake Conversion Kit Single Rear Wheel 1993 & PriorE-Brake kit With Cables and Steel Braided Hoses I don't know if this would work on a D250 with the dana 60 rear. Otherwise converting to rear disc brake on a pickup truck you're likely not going to be rallying would not yield any advantage.

  3. Some help needed with my Dana 70 | Cummins Diesel Forum

    QCLB VP44SO 618 Goerend, 241DLD, 3.55 D70 Powr-lok, DAP .010 VCO, He351W, Hamilton 178/208 and valvetrain, ARP 625, Fleece street head, FASS 150.

  4. dana 70 oil | Cummins Diesel Forum

    Jul 27, 2010 · The problem with only one bottle is the increased amount of fluid the Dana 70 and 80s have over the 60. Seen enough of the 70s eat up the clutches by not adding enough slip lube. When I service any 70 or 80 min amount is 1 1/2 bottles in the 70 and 2 in the 80.

  5. Dana 70 Power Lok Conversion? Can it be done?

    Nov 3, 2018 · I have two Dana 70 axles. One is a '96 out of a Ram 2500 12 valve. The other is an '02 out of a Ram 2500 24 valve. The 96 has the Power Lok limited slip with drum brakes. The 02 in an open diff with disc brakes. Ok here's the big question... Is it possible to take the Power Lok out of the 96 and install it in the 02?

  6. building my dana 70.. - Dodge Cummins Diesel Forum

    Mar 24, 2015 · on ebay ( yeah i know but its from Summit Racing) i found this dana 70 locker that i also found on Cumminsperformanceparts.com -(MOTIVE GEAR) but after doing some research i found on eaton-detroits website with part number references that this specific locker cannot except a 3.54 ring gear but only entertains 4.10 ratio and up. what im here ...

  7. 3.07 gears in Dana 70 question | Cummins Diesel Forum

    Jul 2, 2011 · I currently have an 01 with a 3.55 Dana 70 factory LSD. I'm wanting to know if I can swap in 3.07 gears without changing anything major. I've read a lot of threads about using 3.07 gears in different trucks but I'm confused because of all the different rear ends in the different years and so on. I don't want to change the whole rear end.

  8. Dana 70 1990 w250 cummins | Cummins Diesel Forum

    Dec 11, 2019 · ZK D70-U: USA Standard Master Overhaul kit Dana 70 U differential Tow/haul: 93 Clubcab 4wd flatbed, 5spd, Dana 80 and 35's, Lockright, 3.54, HX35, 5x.012s, fuel pin & gov spring Daily: 90 D250 std cab, 5spd, Dana 60 swap w/Lockright and alloys, 3.54, WH1C

  9. Need info on rear dana 70 hub nut torque specs

    Sep 8, 2014 · 2002 2500 Laramie-28x,xxx miles-NV4500 swap-Dana 80 rear 4.10-2.5in leveling kit-M/T Classic III 16X8 -12mm offset-Primewell Valera HT 265/75R16-fass 150gph-edge comp-high idle/3cyl idle-coolant temp, mpg fooler-bhaf-crankcase vent …

  10. Is this a regular Dana 70 or 70u? | Cummins Diesel Forum

    Oct 31, 2015 · To my understanding a Dana 70 and a Dana 70U are the same unit, or I could be wrong?:confused013: 1984/93 Dodge Crewcab, W350, 1 Ton SRW, long box, 410K Km's, hydroboost, 366 spring, fuel pin to deep side, 14cm housing, Piston LP, PS IC, Isspro Boost, Pyro and tach, NV4500, 29 spline NP205, 3.54's.